Sterile Tech India

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

PRODUCT INTRODUCTION

Sterile Tech ^TM   Fume Exhaust Hoods

 Fume Cupboard is of constant supply air hood with auxiliary bye-pass provision. Three sides of the hood are permanently closed and the front side provided with sliding door..

Inside the working chamber, there will be a sturdy baffle provided at about 200mm above the work-table to uniformly direct the fumes / odour / smoke directly in to the hood’s exhaust system. Suction will be done at three different levels suitable for mild to heavy fumes

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.

The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.

The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).

The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Product Details:

Description:

• Sterile Tech  Vertical Flow Hoods are engineered to deliver the ideal particle-free, bacteria-free clean-air environment needed for laboratory work, testing, developed, inspection, or pharmaceutical procedures. Exclusive design innovations provide exceptional performance in the most challenging environments.
• In vertical flow models, filtered air is passed through the main work chamber of the clean bench in a vertical laminar (unidirectional) air stream on work surface and is exhausted through the holes of work surface.

 

Specification:

• Supply filter: Minipleat type HEPA Filter efficiency 99.99% Down to 0.3µ H-13 Rating.l
• Pre Filter: Micro glass fibre media of EU-4 Ratingl
• Motor Blower Assembly: Centrifugal Blower statically and dynamically balanced with Suitable Rating

 

Technical Details:

Request
Callback

Additional Information:

• Production Capacity: 20unit per month
• Delivery Time: 1 week

Product Details:

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback Request
Callback

Additional Information:

• Production Capacity: 20 unit per month
• Delivery Time: 2 weeks

Product Details:

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback Request
Callback

Additional Information:

• Production Capacity: 20 unit per month
• Delivery Time: 2 weeks

Product Details:

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback Request
Callback

Additional Information:

• Production Capacity: 20 unit per month
• Delivery Time: 2 weeks

Product Details:

Product Details:

Description:

• Sterile Tech  Horizontal Flow Hoods are engineered to deliver the ideal particle-free, bacteria-free clean-air environment needed for laboratory work, testing, developed, inspection, or pharmaceutical procedures. Exclusive design innovations provide exceptional performance in the most challenging environments.
• In vertical flow models, filtered air is passed through the main work chamber of the clean bench in a vertical laminar (unidirectional) air stream on work surface and is exhausted through the holes of work surface.

 

Specification:

• Supply filter: Minipleat type HEPA Filter efficiency 99.97% Down to 0.3µ H-13 Rating.l
• Pre Filter: Micro glass fibre media of EU-4 Ratingl
• Motor Blower Assembly: Centrifugal Blower statically and dynamically balanced with Suitable Rating

 

Technical Details:

Request
Callback

Additional Information:

• Production Capacity: 20 unit
• Delivery Time:  1 week

Request
Callback

Additional Information:

• Delivery Time: 2 weeks

Sterile Tech ^TM   Fume Exhaust Hoods

 Fume Cupboard is of constant supply air hood with auxiliary bye-pass provision. Three sides of the hood are permanently closed and the front side provided with sliding door..

Inside the working chamber, there will be a sturdy baffle provided at about 200mm above the work-table to uniformly direct the fumes / odour / smoke directly in to the hood’s exhaust system. Suction will be done at three different levels suitable for mild to heavy fumes

ume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Request
Callback

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

 

The standard specification of Laboratory Furniture.:

• Sterile Tech India manufacture and supply aesthetically designed all types of laboratory Furniture in various sizes as per the Customer requirement.
• The laboratory tables are fabricated by using pre-treated and electro galvanized iron sheets of suitable thickness and coated with epoxy powder.
• Each bench will be provided with interchangeable under-bench modular storage cabinets.
• These cabinets consist of top drawers with smooth sliding gears. Bottom cup-boards are provided with horizontal inner partition and swing doors with locks.
• All the hardware such as door hinges, door handles, and the locks will be of high quality and are made of stainless steel materials wherever applicable.
• The working top will be made from finely polished black granite. The granite edges are round finished for smooth handling and fatigue-free arm-resting.
• The under bench modules are laid either continuously or alternatively as per the users’ requirement with suitably designed foot-rest wherever required.
• Water sink with high-quality swan neck type is provided and the sink materials will be selected suitably based on the lab activities.
  

Technical Details:

Fume Hood or fume cupboard is typically protected only the user, and are most commonly used in laboratories where hazardous or noxious chemicals are released during testing, research, development or teaching. They are also used in industrial applications or other activities where hazardous or noxious vapors, gases or dust are generated or released. A fume hood is typically a large piece of equipment enclosing five sides of a work area, the bottom of which is most commonly located at a standing work height, Because one side (the front) of a fume hood is open to the room occupied by the user, and the air within the fume hood is potentially contaminated, the proper flow of air from the room into the hood is critical to its function.

Much of fume hood design and operation is focused on maximizing the proper containment of the air and fumes within the fume hood Fume exhausts hoods manufactured by us as per customer requirements:

• The inner wall of the working chamber is covered with epoxy coated or FRP lining or as required.
• The working table is made of acid proof 6mm thick FRP/18mm thick Granite and provided with gas/air Petcocks and additional power points, diffused fluorescent tubes.
• The front shutter is of shatter proof clear glass/poly carbonate sheet, framed in suitable structure with vertically sliding facility and is connected with counter weight balancing arrangement. Fume exhaust hoods are provided with suitable ducting of FRP or PVC material with required diameter, two main types exist, ducted and recirculating (ductless).
• The principle is the same for both types: air is drawn in from the front (open) side of the cabinet, and either expelled outside the building or made safe through filtration and fed back into the room.

Sterile Tech ^TM   Fume Exhaust Hoods

 Fume Cupboard is of constant supply air hood with auxiliary bye-pass provision. Three sides of the hood are permanently closed and the front side provided with sliding door..

Inside the working chamber, there will be a sturdy baffle provided at about 200mm above the work-table to uniformly direct the fumes / odour / smoke directly in to the hood’s exhaust system. Suction will be done at three different levels suitable for mild to heavy fumes

Product Details:

Our company has achieved widespread recognition in providing Powder Dispensing Booth. 

Technical Specification:
• Type: Front Open
• Direction of flow: Vertical
• Cleanliness: Class 100 as per US FED STD 209E (IS 14644-1)
• Equivalent Velocity pressure in mm of WG: 15 mm in filter plenum
• Particle Retention: 0.3 micron
• Noise Level: 65dB on Scale ''A'' ± 5
• Velocity: 100 FPM ± 20%
• Pressure Differential: 0-25 mm Magnehelic Gauge WG
• Pre-Filters: EU 3 grade, Non Oven Synthetic Media washable pre filter
• Front Elevation: PVC Curtain (clear)
• Intermediate Filters: 3 micron & above, HDPE woven mesh, 9 mm Pressure Drop, Efficiency 97%
• HEPA Filters: – Pleat HEPA 99.99% efficiency @ 0.3 micron rating
• Blower Assembly: Statically & dynamically